Just How to Replace a Bathtub Yourself: Removing and also Replacing.
Just How to Replace a Bathtub Yourself: Removing and also Replacing.
Blog Article
We've stumbled upon this post on How to Install a Bathtub down the page on the internet and thought it made sense to discuss it with you on this page.
Mounting a bathtub isn't specifically brain surgery, but it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old tub with a brand-new one is also a moderately hard project. If the old tub is easily obtainable, the job can relocate speedily; if you have to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also set in the new one. Make certain you have actually certified on your own for the job as well as fit attempting it. Rather than employing a service provider to take over a halfway-completed project, it is much better to take into consideration using one before you begin. Chances are you may require a specialist plumber to make tube links.
This article will assist you mount a brand-new bath tub in your bathroom if you have already gotten a new tub and also don't need to alter the plan of your previous water system pipelines.
Your devices and also material checklist should make up the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the water system. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing taps can be quite problematic due to the limited accessibility that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place between the faucet and the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former kind needs to be connected to the tap finishes first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are useful in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression join; then do the exact same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the bathtub as well as also examine the overflow outlet as well as the regular outlet for leakages.
Finally, repair the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the tub has actually been used a minimum of when as this will settle it right into its last position.
Getting ready for the Installment
First of all, the sustaining structure supplied with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the tap features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can move enough to split an inflexible seal, creating the water to pass through the wall between the bath as well as the tiling, causing issues with wetness and also feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as can securing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack rather very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were shown that article on A Step-by-Step Guide to Installing a Bathtub from a good friend on a different web property. Sharing is caring. Helping others is fun. Thanks a lot for taking the time to read it.
Order Repair Report this page